Nova Verta Service
Nova Verta Paint Booth Service and Repair
Independent service for Nova Verta booths. Airflow, heat, filtration, lighting, and controls diagnosed and repaired on-site in Denver, Dallas–Fort Worth, and Tampa Bay.
- Reply within 1 business day
- All makes & models
- Denver · Dallas–Fort Worth · Tampa
What we do
What we do on Nova Verta booths
Nova Verta is a European-built brand. Its booths depend on balanced airflow, reliable heat, and correct filtration, and when finishes drift, that's usually where the answer is. Control generation, burner package, filter sizing, and documentation vary by install year, so we work from the booth you actually have.
Spray Booth Services provides independent service for Nova Verta booths, along with all makes and models. We're a division of John Baker Sales, in business since 2003, and paint booths and the compressors that feed them are all we work on. Whether you need a repair or scheduled maintenance, we'll find the real cause and explain it in plain terms.
Nova Verta systems we service
- Downdraft booths
- AMUs
- Filtration
- Controls
- Lighting
What we handle
How a service visit works
From first call to a booth that runs right
- Step 1
You call or send the form
Call (888) 912-6684 or use the request form. Tell us it's a Nova Verta booth, what it's doing, and when it started. A photo of the data plate helps.
- Step 2
We respond within 1 business day
Every request gets a reply within 1 business day so we can ask the right questions and set a time.
- Step 3
On-site diagnosis
A technician checks airflow, filters, heat, dampers, and controls on your booth as it's actually configured, not from a generic spec sheet.
- Step 4
Clear explanation and quote
We walk you through what we found, what it takes to fix, and what can wait. You approve before work starts.
- Step 5
Repair or schedule
We fix it on the visit when we can, or schedule the repair, parts, or maintenance around your production.
Common Nova Verta booth problems
By the time a shop calls about a Nova Verta booth, three or four small faults are usually stacked up rather than one big failure:
- Hard starts, repeated lockouts, and flame dropout mid-bake from fouled sensors, electrodes out of position, or gas pressure issues.
- Slow heat rise from loaded intake filters, a slipping fan belt, a dirty exchanger, or a damper short of its bake position.
- Lighting that has dimmed or shifted color, leading to color-match comebacks.
- Worn seals and doors out of square letting unfiltered air in at floor level.
- Sensors that drift and interlocks that someone has bypassed to work through a fault.
Our article on Nova Verta booth service goes into each of these in more detail.
What you can check yourself
Some of this is shop-level work you don't need a technician for:
- Read and log the manometer at the same time each day. The trend matters more than any one number.
- Change intake and exhaust filters on readings and a schedule, not on complaint.
- Keep floor grates clear and the cabin swept.
- Wipe light lenses and note any that look yellow or dim.
- Listen for new fan noise and check that belts aren't slipping.
- Inspect door seals for tears, flattening, and gaps.
Logging the manometer is the cheapest early warning you have. See how to read a paint booth manometer.
When to call a technician
Call when the fault involves gas, high voltage, interlocks, or measured airflow: repeated lockouts, temperature that won't hold, a noisy fan, dampers that don't travel, or dirt in the paint after fresh filters. Replacement light fixtures must suit the booth's area classification, so have a technician confirm the rating before ordering. Those are paint booth repair jobs.
If you're not sure how much life is left in the booth, a Paint Booth Evaluation gives you a technician's view before you budget. Smart Filter Monitoring can email you when filter airflow says it's time to change.
Nova Verta is a trademark of its owner. Spray Booth Services is an independent service company and is not affiliated with or endorsed by Nova Verta or any booth manufacturer named on this page.
Questions and answers
Nova Verta booth service questions
Why is my Nova Verta booth taking so long to heat up?
Most often loaded intake filters, a slipping supply fan belt, a fouled heat exchanger, or a damper not reaching its bake position. Change filters first, then have damper travel inspected.
Can you get parts for a European-built booth?
It depends on the component. Many wear items, like belts, bearings, motors, sensors, and filter media, are standard commercial parts. The first step is identifying what's installed.
Do I need special light fixtures in a paint booth?
Yes. Fixtures must suit the area classification where they're installed, and that doesn't change when you switch to LED. See booth lighting problems.
Are you a Nova Verta dealer or authorized service center?
No. Spray Booth Services is an independent service company. We are not affiliated with or endorsed by Nova Verta, and we'll tell you if something needs to go back to the manufacturer.
Can you service a booth you didn't install?
Yes. We work on booths regardless of who sold or installed them.
How quickly do you respond?
We reply within 1 business day. If the booth is down, tell us when you call so we can plan the visit around it.
Where do you provide service?
On-site across the Denver, Dallas–Fort Worth, and Tampa Bay metro areas. Not sure if you're in range? Call and ask.
Where we work
On-site service in Denver, Dallas–Fort Worth & Tampa
We provide hands-on booth and compressor service in these regions. Not sure if you're in range? Call and ask.
- Denver, CODenver metro and the Front Range
- Dallas–Fort Worth, TXThe greater DFW metroplex
- Tampa, FLTampa Bay and surrounding area
Outside these areas? We can come to you when technician travel is covered.
All service areas →Guides
Related guides
Ready when you are
Get your Nova Verta booth running at its best
Tell us what's going on and we'll get you scheduled.
Prefer to send a request?
We reply within 1 business day.