Marine & Boat Finishing

Marine and Boat Paint Booth Service

Boat finishing means big surfaces, long hulls, and humid air working against the finish. We keep marine booths and the compressed air behind them running clean, dry, and balanced in Tampa Bay, Dallas–Fort Worth, and Denver.

  • Reply within 1 business day
  • All makes & models
  • Denver · Dallas–Fort Worth · Tampa
Large green industrial paint booth with its tall doors open

What we do

Booth service for marine and fiberglass refinishing

Marine refinishing is finishing on hard mode: large surface areas, long hulls, demanding coatings, and humidity that gets into everything. We service large enclosed and open marine booths, plus the compressed-air systems and dryers that keep moisture out of your coats.

Spray Booth Services is a division of John Baker Sales, in business since 2003, and paint booths and the compressors that feed them are all we work on. One call covers the booth and the air that feeds it.

Systems we service

What we handle

Large-surface airflowBalanced air across big enclosures and long hulls, with dead spots found and fixed.
Moisture controlCompressor, dryer, and drain service to keep water out of the air lines. See water in your air lines.
FiltrationCorrect intake and exhaust media for clean air on demanding coatings, changed on pressure readings.
Burners & heatCure systems checked and repaired so temperature holds through long jobs.
Enclosed & open boothsWe service the booth layouts marine shops run.
Seals & corrosionDoor seals, panels, ductwork, and stacks checked for leaks and for corrosion where humid air and condensate collect.

How a service visit works

From first call to a booth that runs right

  1. Step 1

    You call or send the form

    Call (888) 912-6684 or use the request form. Tell us the booth size, what you spray, and what's showing up in the finish.

  2. Step 2

    We respond within 1 business day

    Every request gets a reply within 1 business day so we can ask the right questions and set a time.

  3. Step 3

    On-site diagnosis

    A technician checks airflow, filters, heat, controls, and the compressed-air supply to find the actual cause.

  4. Step 4

    Clear explanation and quote

    We walk you through what we found, what it takes to fix, and what can wait. You approve before work starts.

  5. Step 5

    Repair or schedule

    We fix it on the visit when we can, or schedule the work between hulls.

What humidity does to a marine finish

Humid air is hard on a finish in two ways. In the air lines, moisture that gets past a failing dryer or a stuck drain shows up as fisheyes, blush, and adhesion problems. In the booth, humid conditions slow flash times and can cause blush in some coatings. Read what heat and humidity do to your booth.

Signs your marine booth needs service

  • Fisheyes, blush, or water spots that point to wet compressed air.
  • Overspray hanging around the hull or settling back on wet coating.
  • Filters loading unevenly along a long booth.
  • Cure temperatures that drift through long holds.
  • Rust or corrosion on stacks, duct joints, or door frames.
  • Doors and seals that no longer close tight against the shop.

Big hulls, big airflow

A hull takes up a large share of the booth's cross-section, so air takes the easy path around it and can leave low-velocity zones that hold vapor and drop contamination. We take readings at multiple points, check filter loading along the length of the booth, and look at fans, dampers, and plenum condition. More in our marine and fiberglass refinishing booth service guide.

If you're unsure how much life is left in an older booth, start with a Paint Booth Evaluation.

Questions and answers

Marine booth service questions

More answers in the FAQ →
Can you handle large hulls and big enclosures?

Yes. We balance airflow across big enclosures and long hulls and take readings at multiple points rather than relying on one gauge.

How do you deal with Florida humidity in the finish?

Moisture control starts at the compressor. We service compressors and dryers, drains, and filters to keep water out of your coats, and check that the booth itself holds its pressure balance.

Do you service the compressor and dryer too?

Yes. Booth problems and air problems often show up together, so we look at both. See compressor service.

How often should a marine booth be serviced?

Filters change on pressure readings, and a full professional pass is typically once or twice a year depending on hours. Humid climates and long jobs often call for more frequent checks on dryers and drains. See the Booth Uptime Plan.

Which brands do you service?

All makes and models, including GFS, Binks, and DeVilbiss.

How quickly do you respond?

We reply within 1 business day. If the booth is down, tell us when you call so we can plan the visit around it.

Where do you provide service?

On-site across the Denver, Dallas–Fort Worth, and Tampa Bay metro areas. Not sure if you're in range? Call and ask.

Where we work

On-site service in Denver, Dallas–Fort Worth & Tampa

We provide hands-on booth and compressor service in these regions. Not sure if you're in range? Call and ask.

Map of the United States with our service areas: Denver, Dallas–Fort Worth and Tampa Denver Dallas–Fort Worth Tampa

Outside these areas? We can come to you when technician travel is covered.

All service areas →
Clean downdraft paint booth with its doors open, ready for production

Ready when you are

Get your booth running at its best

Tell us what's going on and we'll get you scheduled.

Prefer to send a request?

We reply within 1 business day.