How a paint booth works

How a paint booth works

A plain-English guide to what a paint booth does, how air moves through it from intake to stack, how spray and bake modes differ, and the main kinds of booth and when each is used.

  • Reply within 1 business day
  • All makes & models
  • Denver · Dallas–Fort Worth · Tampa
Crossdraft airflow: in through the front filters, out through the back-wall exhaust

What a booth does

Four jobs, one enclosure

Every paint booth, from a small open-face bench booth to a production line, does the same four things.

Supplies clean, controlled airFiltered air comes in at a steady rate, so dust and dirt stay out of the wet paint.
Carries overspray awayThe same airflow moves overspray and fumes away from the painter and the part, into the exhaust filters.
Heats for flash and cureMany booths heat the air to speed up flash-off between coats and to bake the finish.
Lights the workBright, even light lets the painter see coverage, color and defects while they spray.

The air path

How air moves through a booth, step by step

This is the path in a typical heated downdraft booth. Other booth types move the air in a different direction, but the stages are the same.

  1. Step 1

    Outside air

    Fresh air is drawn in from outside the building.

  2. Step 2

    Air make-up unit and intake filters

    The air make-up unit (AMU) pulls the air in through intake filters that catch the coarse dirt.

  3. Step 3

    Heater

    A burner in the AMU warms the air to the temperature the booth is set to.

  4. Step 4

    Plenum

    The air fills the plenum, the space above the ceiling, so it spreads out evenly.

  5. Step 5

    Ceiling filters

    Fine ceiling (diffusion) filters clean the air again and spread it gently over the cabin.

  6. Step 6

    Cabin

    The air moves down past the vehicle or part, carrying overspray with it.

  7. Step 7

    Exhaust filters

    Exhaust filters, in a floor pit or in the back wall, capture the overspray.

  8. Step 8

    Exhaust fan

    The exhaust fan pulls the air through the filters and out of the booth.

  9. Step 9

    Stack

    The air leaves the building through the exhaust duct and stack.

Spray mode and bake mode

Two ways a booth runs

Spray mode

While painters are spraying, the booth brings in fresh outside air, warms it to a comfortable spray temperature and sends all of it out through the exhaust. Fresh air in and all air out keeps overspray and fumes moving away from the painter and the finish.

Between coats, the booth keeps running so each coat can flash off before the next one goes on.

Bake or cure mode

Once spraying is done, a heated booth can switch to bake (cure) mode and raise the temperature to dry and harden the finish. On many booths, dampers switch over so most of the heated air recirculates through the booth instead of going straight out, with some fresh air still mixed in. That is how the booth reaches and holds cure temperature.

Bake temperatures and times come from the paint supplier's data for the product you are using.

Pressure balance

Why a booth runs slightly positive

A booth is balanced when the air coming in and the air going out are set to work together. Most booths are set to run slightly positive: a little more air in than out. That small push keeps the cabin from pulling dirty shop air in through door gaps and seams.

Manometers (pressure gauges) on the booth show the pressure across the filters and, on many booths, the cabin pressure. Watching them is how you see the balance changing as filters load.

  • Clean filters: the booth holds the balance it was set to
  • Loaded intake filters: less air gets in, and the cabin drifts negative, pulling dirt in through the doors
  • Loaded exhaust filters: less air gets out, so pressure climbs more positive, overspray lingers and doors can push open or be hard to close

Lighting and controls

Seeing the finish, and running the booth safely

Lighting

Booth lights sit in the ceiling, the upper side walls or both, behind sealed glass panels that keep overspray off the fixtures. The goal is bright, even light from several angles, so painters can see coverage, color and small defects before the finish cures. Dirty lenses and failed tubes make the booth darker over time, which is why lighting is part of every service visit.

Controls and safety interlocks

The control panel runs the fans, the burner, the lights and the switch between spray and bake. Interlocks tie these together: for example, the exhaust fan has to be running and air has to be moving before spraying can start, and the burner has its own flame safety controls.

Burner, gas and electrical work is for qualified technicians only. If a booth faults, note any codes on the panel and call a technician instead of bypassing a control.

Kinds of paint booth

Booth types and when each is used

The main difference between booth types is which way the air moves past the part. The diagrams show the airflow for the main types.

Crossdraft

Air comes in through filters in the doors or front wall, moves horizontally across the vehicle or part, and leaves through exhaust filters in the back wall.Used for: Smaller shops, general refinishing and many industrial parts.

Full downdraft (pit)

Air comes in through the ceiling filters, moves straight down past the vehicle and leaves through floor grates into an exhaust pit.Used for: Collision and automotive refinishing where a clean finish matters most.

Raised (basement) downdraft

The same top-to-bottom airflow, but the booth sits on a raised steel base that takes the exhaust instead of a pit dug into the floor.Used for: Downdraft results where a pit cannot be dug.

Semi-downdraft

Air comes in through ceiling filters at the front of the booth, moves down and back, and leaves through exhaust filters low in the back wall.Used for: Shops that want downdraft-style airflow without a pit.

Side downdraft

Air comes in through the ceiling, moves down past the vehicle and leaves through exhaust filters low on the side walls.Used for: Downdraft-style airflow without a pit, with exhaust along the sides.

Open-face and bench booths

A booth with an open front. Air is drawn from the shop past the painter and the part into exhaust filters in the back wall.Used for: Smaller parts, touch-up work and woodworking.

Prep stations

A curtained area with filtered air from above and exhaust at floor level or the back, for sanding, priming and prep work.Used for: Prep and primer work, so the main booth stays free for topcoats.

Enclosed industrial and conveyor booths

Large enclosed booths for big parts and equipment, and production booths where parts move through on a conveyor.Used for: Manufacturing, heavy equipment and finishing lines.

Powder coating booths

Airflow pulls oversprayed powder into cartridge filters; many booths recover the powder to reuse it. Parts cure in a separate oven.Used for: Powder coating lines and job shops.

What wears

What needs regular service

These are the parts that wear, load up or drift out of adjustment in normal use.

FiltersIntake, ceiling and exhaust filters load up and need changing.
BeltsFan belts stretch and slip, which quietly drops airflow.
MotorsFan motors wear and can overheat or trip.
BearingsWorn bearings get noisy and can stop a fan.
BurnersBurners need tuning and checks to light reliably and reach temperature.
DampersDampers stick or drift, which upsets spray and bake airflow.
Door sealsSeals flatten and leak, letting dirt in and throwing off pressure.
LightsLenses get dirty and tubes fail, so the booth gets darker.

Questions and answers

Paint booth basics: questions and answers

More answers in the FAQ →
What is booth 'airflow balance'?

How the air pushed in compares with the air pulled out. Most booths run slightly positive to keep dirt out; a booth that goes negative pulls dirty shop air in through the doors. Our Booth Uptime Plan keeps it checked.

What does the manometer tell me?

The pressure difference across a set of filters (and on some booths, the cabin pressure). A low reading across a filter means it is clean; the reading climbs as the filter loads, which tells you it is time to change it.

Why does my booth need an AMU?

It supplies the clean, heated air that carries overspray away and cures your coating. Most airflow and heat problems trace back to it.

Clean downdraft paint booth with its doors open, ready for production

Ready when you are

Get your booth running at its best

Tell us what's going on and we'll get you scheduled.

Prefer to send a request?

We reply within 1 business day.