Accudraft Service
Accudraft Paint Booth Service and Repair
Independent service for Accudraft booths. Controls, burner sequence, airflow, and seals diagnosed and repaired on-site in Denver, Dallas–Fort Worth, and Tampa Bay.
What we do
What we do on Accudraft booths.
Accudraft builds many booth configurations: downdraft and semi-downdraft, direct-fired and indirect-fired, with different control generations and burner packages depending on the year. The same symptom can point to different causes on two booths wearing the same badge, so diagnosis often starts at the control panel, sensors, and burner sequence and works out from there.
Spray Booth Services provides independent service for Accudraft booths, along with all makes and models. We're a division of John Baker Sales, in business since 2003, and paint booths and the compressors that feed them are all we work on. Whether you need a repair or scheduled maintenance, we'll find the real cause and explain it in plain terms.
What we handle
Control & panel diagnostics
Panel faults, interlock chains, and sensors read and traced correctly before parts get replaced.
Burner sequence
Ignition, flame sensing, and staging brought back to reliable operation.
Airflow & balance
Velocity and pressure restored for clean finishes and steady bake temperature.
Sensors & safeties
Temperature and pressure sensors checked; safeties verified, never bypassed.
Filtration
Correct filters fitted, frames sealed, and restrictions cleared.
Preventive maintenance
Controls, dampers, and the air make-up unit kept in working order on a schedule.
Accudraft systems we service
- Downdraft & semi-downdraft
- Control packages
- AMUs
- Burners
Currently serving Denver, Dallas–Fort Worth, and Tampa Bay.
How a service visit works
From first call to a booth that runs right.
You call or send the form
Call (888) 912-6684 or use the request form. Tell us it's an Accudraft booth, what it's doing, and when it started. A photo of the data plate helps.
We respond within one business day
Every request gets a reply within one business day so we can ask the right questions and set a time.
On-site diagnosis
A technician checks airflow, filters, heat, dampers, and controls on your booth as it's actually configured, not from a generic spec sheet.
Clear explanation and quote
We walk you through what we found, what it takes to fix, and what can wait. You approve before work starts.
Repair or schedule
We fix it on the visit when we can, or schedule the repair, parts, or maintenance around your production.
Common Accudraft booth problems
Most Accudraft service calls start with a job that came out wrong, not a blinking light. The patterns we see most:
- Bake temperature that climbs slowly or stalls short of setpoint, often loaded intake filters or a recirculation damper not reaching its bake position.
- Burner staging or modulation not stepping up, or gas pressure sagging under full fire.
- Dirt and nibs in the finish from torn or bypassing filters, a dirty plenum, or a cabin not holding positive pressure.
- Weak airflow from loaded exhaust filters, slipping belts, or a fan wheel caked with overspray.
- A control panel that won't start a cycle because one device in the interlock chain is open.
Our article on Accudraft booth service goes into each of these in more detail.
What you can check yourself
Some of this is shop-level work you don't need a technician for:
- Read and log the manometer at the same time each day. The trend matters more than any one number.
- Change intake and exhaust filters on readings and a schedule, not on complaint.
- Keep floor grates clear and the cabin swept.
- Wipe light lenses and note any that look yellow or dim.
- Listen for new fan noise and check that belts aren't slipping.
- Inspect door seals for tears, flattening, and gaps.
Logging the manometer is the cheapest early warning you have. See how to read a paint booth manometer.
When to call a technician
Stop at anything involving the gas train, burner adjustment, high-voltage wiring, drive components, damper actuators, or safety devices. A control panel that refuses to start is usually protecting you from something, and an interlock should never be jumpered to get a car out the door. Those are paint booth repair jobs.
If you're not sure how much life is left in the booth, a Booth Health Check gives you a technician's view before you budget. Smart Filter Monitoring can email you when filter airflow says it's time to change.
Accudraft is a trademark of its owner. Spray Booth Services is an independent service company and is not affiliated with or endorsed by Accudraft or any booth manufacturer named on this page.
Questions & answers
Accudraft booth service questions
Why is my Accudraft booth not reaching temperature?
Usually loaded filters, a damper not fully repositioning for bake, a burner not staging up, gas pressure dropping under load, or a sensor reading incorrectly. Which one applies depends on your booth's firing type and control generation, so have it verified on site.
Can I reset a control panel fault myself?
Resetting once is reasonable. Resetting repeatedly is not: a fault that keeps returning means a device is doing its job and something upstream is wrong. See control panel faults.
How often should the filters be changed?
Go by manometer readings and your manufacturer's stated limits, not the calendar. A production shop loads filters far faster than one spraying a few panels a week.
Are you an Accudraft dealer or authorized service center?
No. Spray Booth Services is an independent service company. We are not affiliated with or endorsed by Accudraft, and we'll tell you if something needs to go back to the manufacturer.
Can you service a booth you didn't install?
Yes. We work on booths regardless of who sold or installed them.
How quickly do you respond?
We respond to every request within one business day. If the booth is down, tell us when you call so we can plan the visit around it.
Where do you provide service?
On-site across the Denver, Dallas–Fort Worth, and Tampa Bay metro areas. Not sure if you're in range? Call and ask.
Where we work
On-site service in Denver, Dallas–Fort Worth & Tampa.
We provide hands-on booth and compressor service in these regions. Not sure if you're in range? Call and ask.
Service currently limited to the Denver, Dallas–Fort Worth, and Tampa metro areas.
From our resources
Keep learning.
Guides from our team to help you get more out of your booth.
Ready when you are
Get your Accudraft booth running at its best.
Tell us what's going on and we'll get you scheduled. We respond to every request within one business day.
We reply within 1 business day.